Grind & Polish
Polished Concrete Floors in Granbury, TX
Residential and commercial polished concrete across Granbury, Weatherford, Stephenville, Glen Rose, Aledo & the southwest Fort Worth area. We grind your existing slab with progressively finer diamonds, harden it with a densifier, and polish it to the sheen you want. Nothing gets added on top, so there is nothing to peel.
Start here
What polished concrete actually is
Every other floor we install adds something to your slab. Polished concrete takes something away. The shine is the concrete itself, refined until it reflects light.
The work runs in three stages. We grind the slab with diamond tooling, starting coarse and stepping through progressively finer grits. We apply a densifier that soaks in and chemically hardens the surface, which is what lets it take a polish and resist wear. Then we polish through the finer grits to the sheen level you picked.
No epoxy. No flake. No film of any kind. That single fact is the whole argument for polished concrete: a coating can peel because it sits on the slab, and polished concrete cannot, because it is the slab.
Two decisions
How your polished floor will look
Two choices set the final look, and they are independent of each other.
How much aggregate shows
How aggressively we grind decides what you see in the floor. Grind lightly and you keep the smooth cream layer on top, which reads as a fairly uniform surface. Grind deeper and you start exposing the sand, giving a speckled salt-and-pepper look. Deeper still and you expose the larger stone in the mix, which reads almost like terrazzo.
Worth knowing: how much aggregate is available depends on how your slab was poured and how flat it is. We can tell you what your specific floor will realistically give you, but nobody can promise a particular aggregate look on a slab they have not ground.
How much it shines
Sheen runs from a low matte with a soft glow up to a high gloss that reflects the room. Higher gloss means more passes with finer abrasives, which means more labor and more cost. It also shows footprints and dust more readily. Most homes land somewhere in the middle.
Inside the house
Residential polished concrete floors
If your home is on a slab, you already own the floor. Polishing is a way to use it instead of covering it.
Living rooms, kitchens, and open plans. One continuous surface with no seams, no grout, and no transitions between rooms. It is hard to make a space feel bigger more cheaply than removing every line from the floor.
People with allergies. No carpet fibers and no grout lines means dust has nowhere to live. It sweeps and damp-mops, and that is the whole maintenance routine.
Homes with radiant heat. Concrete holds and radiates heat well, and there is no insulating layer between the slab and the room.
Pulling up carpet or tile. Once the old flooring and its adhesive come off, the slab underneath is the candidate. Adhesive residue, tack strip marks, and patches all affect the result, so we look before we promise anything.
Straight comparison
Polished concrete vs epoxy vs stained concrete
We install all three, so we have no reason to push you toward one. They solve different problems.
| Polished concrete | Stained concrete | Epoxy flake | |
|---|---|---|---|
| What it is | The slab, refined | The slab, colored | A coating on the slab |
| Can it peel? | No | Sealer can wear | Only if built wrong |
| Hides slab damage | No | No | Yes |
| Color options | Limited to the concrete | Stain colors | Any flake blend |
| Recoating | Never | Reseal periodically | Topcoat eventually |
| Best for | Interior living space | Budget, natural look | Garages, shops, hard use |
The short version: if your slab is in good shape and you want a floor that never needs recoating, polish it. If you want color for less money, stain it. If the slab is rough and you want it covered and armored, a flake coating is the answer. You can also stain a floor and then polish it, which is where a lot of the nicest interior floors land.
Read this first
What polishing will not do
It does not hide anything
Polishing works with the slab you have. Cracks, patches, and color variation stay visible, and grinding can reveal variation you did not know was there, because you are cutting into concrete that has never been exposed. If you want a uniform floor over a damaged slab, a coating is the right call.
Your slab decides what is possible
Flatness, how the slab was finished, how much aggregate sits near the surface, and what has been glued to it all shape the outcome. That is why we assess the concrete before quoting a look, rather than showing you a photo of somebody else's floor and implying yours will match.
It is not the cheapest option
Polishing is labor. Multiple passes with progressively finer diamonds across your whole floor takes time, and higher gloss takes more of it. If budget is the main constraint and you mostly want the slab finished and sealed, stain and seal gets you there for less.
For business
Commercial polished concrete
Retail floors, showrooms, offices, restaurants, and warehouses all polish well, and the maintenance case is strong: no waxing, no stripping, no tile to replace, and a surface that gets harder rather than wearing out. For large commercial floors, the fact that there is no coating to reapply on a cycle is usually the deciding factor.
Where polishing is the wrong answer commercially is a floor that takes chemical spills, hot tires, or heavy impact. Those want a coating instead. See commercial floor coatings for the heavier systems, or quartz broadcast if grip and abrasion resistance are the priority.
Send us a photo of the slab
Polished concrete depends more on the concrete you already have than anything else we do. A couple of photos and the square footage tell us a lot, and we will tell you honestly whether your slab is a good candidate or whether your money goes further on a coating. Serving Granbury, Weatherford, Stephenville, Glen Rose, Aledo & the southwest Fort Worth area.