The Topcoat
Polyaspartic Floor Coating in Granbury, TX
Polyaspartic is the layer you walk on: UV-stable, hard-curing, and built to take hot tires. We install it over a bonded epoxy base rather than straight onto concrete, which is the difference between a floor that lasts and one that peels. Serving Granbury, Weatherford, Stephenville, Glen Rose, Aledo & the southwest Fort Worth area.
Start here
What polyaspartic is
Polyaspartic is a fast-curing coating with a specific set of strengths: it stays clear under UV instead of yellowing, it cures hard, it resists chemicals and stains, and it shrugs off hot-tire pickup.
Chemically it is a type of polyurea. Raw polyurea sets in seconds, which is impossible to place well by hand, so chemists slow the reaction down. That slowed-down, workable version is polyaspartic. The good ones are "aliphatic," which is the property that keeps them clear in sunlight.
Its one limitation is thickness. Polyaspartic goes on as a thin film, so it makes an excellent topcoat and a poor base coat. Laid straight onto concrete with nothing underneath, a thin film has very little to hold back what a slab pushes at it.
The comparison everyone searches
Polyaspartic vs epoxy
People treat these as rival products you choose between. They are two parts that do different jobs, and the best floors use both.
Epoxy: the better base
- Goes on thick and builds genuine film
- Has the working time to key into ground concrete
- Handles moisture pushing up through the slab
- Ambers with steady direct sun, so a poor topcoat
Polyaspartic: the better topcoat
- UV stable, stays clear instead of yellowing
- Cures hard and fast
- Resists hot-tire pickup, chemicals, and stains
- Thin film, so a poor base coat on its own
Put plainly: epoxy against the concrete, polyaspartic against the sun and your tires. When a company tells you their coating beats epoxy, ask what is touching the slab. We go deeper in the truth about 1-day floors and in our layer-by-layer system breakdown.
How we build it
Our polyaspartic garage floor system
- Diamond-grind the slab. Opens the concrete so the coating keys into it instead of sitting on top, and takes off whatever the floor has absorbed.
- Meter the concrete for moisture. We write the reading on your work order. Moisture is what lifts coatings, so the number decides the system.
- High-build, 100% solids epoxy moisture-vapor-barrier base. Bonded into the ground slab. This is the layer a 1-day floor skips.
- Full flake broadcast in the color you pick, thrown to rejection.
- UV-stable polyaspartic topcoat. The wear surface, and the reason the floor still looks right in year ten.
The epoxy base has to cure overnight before the polyaspartic goes down, which is the only reason our install takes two days. That cure time is what makes the floor last, not a delay to apologize for.
Worth knowing
Why "1-day polyaspartic" floors peel
Polyaspartic cures fast enough that a crew can do a whole floor in a day. That speed is the pitch. What it costs you is the base coat.
A 1-day install uses a thin, fast-curing polyaspartic or polyurea base instead of an epoxy moisture barrier. Both crews grind the slab, so that is not the difference. The difference is that the thin base flash-cures in minutes, before it can soak into the open pores of the ground concrete, so it bonds to the surface instead of locking into it.
Then moisture does the rest. Concrete is never fully dry, water vapor rises through it constantly, and when it reaches a thin film with nowhere to go it collects underneath and pushes the coating off. Add a Texas summer with hot tires and the failure speeds up.
Ask any installer three things: does an epoxy base coat go against my concrete, do you meter the slab for moisture before quoting, and does the warranty cover moisture without an exclusion. The answers tell you which floor you are buying. Our warranty guide covers what to look for in the fine print.
Where it goes
Where a polyaspartic coating belongs
Garages. The main one. Hot tires, dropped tools, oil, and Texas heat are exactly what polyaspartic handles, and the flake underneath hides wear. See garage floor coating in Granbury or pick your town from the footer.
Shops and auto bays. Oil and solvents wipe off a sealed floor. More on shop floor coating.
Commercial floors. Retail, offices, warehouses, and showrooms, where the topcoat takes the traffic. See commercial floor coatings.
Patios and exterior concrete. UV stability matters most outdoors, which is where a polyaspartic topcoat earns its keep. See patio coating.
Where it is not the answer: a slab you want left looking like concrete. For that, polished concrete or stained concrete finish the slab rather than covering it.
Get your price before we visit
Residential garages are a flat $6 per square foot, all-inclusive, so a typical two-car runs about $3,000 to $3,600. No home visit needed to get a number. Commercial is quoted per project.